半导体激光器温度调谐波长扫描技术

低成本、小型化的波长扫描半导体激光器在光纤传感系统中有着重要作用。设计了一种可进行温度调谐的半导体激光光源驱动电路。该电路系统以ARM单片机作为控制中心,利用热敏电阻采样激光工作温度,并通过半导体制冷器(TEC)进行温度调节,使得激光器能够根据温度调谐实现波长扫描；同时通过背向光探测器(PD)采样激光输出功率,并通过改变半导体激光驱动电流实现对激光输出功率的控制,使得激光器在温度变化时输出光功率保持稳定。实验结果表明,该电路能够长时间可靠地工作,激光器能够实现的最大波长调谐范围为5nm,且输出光功率在整个波长扫描过程中保持稳定。     

A dense and compact laser cladding layer with solid metallurgical bonding significantly improved corrosion resistance of Mg alloy for engineering applications

Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm² for Mg alloy to 13 μA/cm² for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications.     

BRISOL钠同位素放射性核束的产生

北京放射性核束装置在线同位素分离器（BRISOL）采用100 MeV、200 μA回旋加速器提供的质子束打靶产生中、短寿命放射性核束，在线分析后供物理用户使用，其质量分辨率好于20 000。为开展²⁰Na核的奇异衰变特性研究，研制了氧化镁靶，并采用100 MeV质子束轰击氧化镁靶在线产生了^20～26Na⁺的钠同位素放射性核束。当质子束流强为8 μA时，²⁰Na⁺离子束的最大产额为2×10⁵ s^-1，²¹Na⁺离子束的最大产额为4×10⁸ s^-1。完成了北京放射性核束装置首个放射性核束物理实验，累计供束近200 h。     

钛合金激光清洗及其对激光焊接气孔的影响

采用砂纸打磨、酸洗、激光清洗等方式对Ti6Al4V钛合金进行焊前清洗。通过扫描电镜、白光干涉仪、能谱仪分析了各种清洗方式下的表面形貌、粗糙度和化学成分，研究了不同清洗方式及参数对清洗效果的影响。在均匀熔透和表面质量良好的同一激光焊接条件下，比较了不同清洗条件对气孔率的影响。合适的激光清洗可有效清除焊接试件表面氧化层，并改善表面粗糙度，得到较低的气孔率，其焊缝可达到中国航天工业行业标准I级焊缝要求。     

Investigation of spitting behaviour of NiCoCrAlY type materials during electron beam evaporation

ABSTRACT

Spitting behaviour of four casted and powder metallurgy ingots used in the fabrication of NiCoCrAlY-type environmental protective coatings by electron beam physical vapour deposition was investigated and correlated with ingot microstructures and compositions. Spits found in the coatings mainly consisted of the Ni₅Y phase precipitated in the β-NiAl matrix while their typical size exceeded 50?µm. Spitting was less pronounced for ingots having a higher Cr content, larger size of γ-Ni(Co, Cr) precipitates formed within β-NiAl grains and narrower transitional zone formed at the interface between molten and unmolten ingot regions and consisting of coarsened β grains. Large (above 100?µm) agglomerates of the Ni₅Y phase detected below the zone were identified as the main spit precursors.     

焊缝表面缺陷激光扫描三维重构测量

为检测工件焊缝表面缺陷，采用点激光位移传感测距法和数据拟合技术进行焊缝表面缺陷检测试验研究. 首先采集缺陷表面轮廓数据点，利用高斯滤波对原始数据降噪处理. 再对处理后的数据点进行Delaunay三角剖分，使散乱点连接并结合其空间坐标重构出缺陷的三维模型. 结果表明，基于点激光位移传感测距技术及焊缝表面缺陷三维重构方法可以准确判断焊缝成形情况.     

卫星激光通信粗跟踪系统复合控制策略

针对卫星激光通信粗跟踪系统的跟踪稳定精度指标要求高的特点,建立了基于永磁同步电机直接驱动的粗跟踪系统模型并进行了跟踪稳定误差分析。在采用传统PID控制策略存在跟踪误差较大、动态性能较差等不足的基础上,提出了一种基于粗跟踪系统的改进型前馈复合控制策略。从理论上分析了前馈复合控制策略提高了粗跟踪系统的动态性能,为降低跟踪稳定误差提供了改善方案。地面实验验证结果表明,与传统控制策略相比,改进型复合控制策略极大地降低了系统的动态跟踪误差,动态跟踪误差由606μrad降低至13μrad(1δ)。进一步的在轨实验也验证了改进型复合控制策略的合理性和先进性,总体指标满足了卫星激光通信终端的极高精度要求。本文所提出的控制策略对其他高性能跟踪伺服系统设计也具有较大的借鉴意义。